We make every attempt to provide as much information as possible on the mixing and application of Antel’s Epoxy Flake Flooring System, however, if there is something you are not sure of, or if you have a particular request or problem, please don’t hesitate to contact us and we will only be too happy to help. Antel is committed to providing a superior before and after sales service.There are four steps to the entire process. It is advisable to use a barrier cream and gloves when applying.įOR FULL DETAILS PLEASE REFER TO HEALTH & SAFETY DATA SHEET. A shelf life in excess of 12 months can be expected for unopened containers kept in the above conditions.Īpplication equipment used should not be cleaned with water, but simply allowed to cure/harden and then disposed of.Īntel Epoxy Flake Flooring System is much safer to handle than other resin systems however, it is recommended that all skin contact is avoided and that if contact is made, are washed immediately with soap and warm water. Store in a cool, dry and frost free area in original containers. This is a guide only and will depend on temperature and application thickness of the Sealer Coat. We recommend waiting 1-2 days before light traffic and 4-5 days before heavy traffic. Maximum cure, hardness and chemical resistance is obtained within 7 days. Apply the Sealer Coat using a foam roller.Īt 20 ☌, and with reasonable ventilation, the coating is touch dry in 8 hours and hard dry in 12 hours. Pour the contents of the B Pack into the larger A Pack.ġ3. Mix the Sealer Coat B Pack thoroughly.ġ2. Mix the Sealer Coat A Pack thoroughly.ġ1. A tyrolean/flicker gun will make this much easier.ġ0. While wearing spiked shoes, broadcast PVA flake as evenly as possible over the area. Apply the Base Epoxy Resin using a medium pile roller or brush.ħ. Pour into at least one roller tray to maintain pot life.Ħ. Mix again thoroughly (ideally with a mixer paddle) for a minimum of three minutes, so that the two components are completely mixed.ĥ. Pour the contents of the B Pack into the larger A Pack.Ĥ. Mix the Base Epoxy Resin B Pack thoroughly.ģ. Mix the Base Epoxy Resin A Pack thoroughly.Ģ. If unsure, please contact us for technical advice.ġ. We recommend wearing spiked shoes when applying the Flake. The material will become unworkable once outside of this pot life. If you are applying the coating in higher temperatures, the pot life may be reduced. This is based on a temperature of 20 ☌/68 ☏. The pot life of the Base Coat and Sealer Coat is approximately 45 mins. If there are any leaks, these should be repaired with Antel Waterstop or Antel Epoxy Putty before application. All voids and surface imperfections must be carefully filled.Įpoxy Flake Flooring System can be applied to fibreglass but it's important the surface is mechanically sanded to provide a key.Ĭlean the surface you will be applying the Epoxy Flake Flooring System to. Particular attention should be made to degreasing surfaces before application. If applying to a surface that hasn’t previously been painted or is porous, one coat of Epoxy Solvent Free Primer will need to be applied before applying Epoxy Flake Flooring System.Īll surfaces should be dry. If applying over an existing coating or to a non-porous surface, mechanically sand the area to create a key. THE PERFORMANCE OF THE COATING CAN BE SERIOUSLY IMPAIRED IF THE FOLLOWING INSTRUCTIONS ARE NOT STRICTLY ADHERED TOĭo not apply in temperatures below 10 ☌/50 ☏.Īlthough Epoxy Flake Flooring System will overcoat most other finishes and paints, the best results are achieved when surfaces are clean and free of other finishes/coatings. With rougher and more porous surfaces, the coverage of the Base Epoxy Resin may be reduced. 2.5 KG of Base Epoxy Resin (A & B Pack)ĭepending on the substrate, coverage is approximately 5-6 square metres per pack, on a non porous, relatively smooth surface. The scope of applications for Antel Epoxy Flake Flooring System is extensive and it can be used virtually anywhere that requires an attractive hard wearing, anti-slip floor. Antel Epoxy Flake Flooring System is a three part system, consisting of one coat of base epoxy resin, PVA flake and a top sealer coat to protect the underlying flake, while adding increased gloss, chalk resistance and chemical resistance.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |